Scion Keyless Entry Remote Fob Programming Instructions

2004 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
3. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2004 Toyota Scion Tc Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2005 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
3. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2005 Toyota Scion Tc Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2006 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
3. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2006 Toyota Scion Tc Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2007 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
3. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2007 Toyota Scion Tc Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2008 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
3. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2008 Toyota Scion Tc Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2009 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
3. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2009 Toyota Scion Tc Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2010 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

Have all transmitters for the vehicle at hand

1. With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
2. Within 5 seconds,
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
   Insert the key into the ignition (Do NOT Turn it) and Pull key out.
3. Within 40 seconds,
Close then open the drivers door.

Close then open the drivers door.

Insert the key into the ignition (Do NOT Turn it) and Pull key out.
1. Within 40 seconds.
Close then open the drivers door.

Close then open the drivers door.

Insert the key into ignition and leave it in the ignition.

Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).

Remove the key from the ignition.
1. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
2. Within 40 second,
A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.

B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.

Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.

(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
1. Open drivers door.

Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.

1. Make sure all doors are closed
2. Open Driver’s door
3. Insert key into ignition, then remove it
4. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
5. Close and re-open driver’s door
6. Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
7. Insert key into ignition switch
8. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
9. Remove Key from ignition
10. Door locks should cycle to confirm entry into programming mode
a. AVALON – Press LOCK on remote for a minimum of 1 second

b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
1. Locks should cycle once to confirm programming. If they cycle twice, the programming failed
2. Repeat button procedure to program remaining remotes
3. Close driver’s door. Test remotes.

2010 Toyota Scion Tc Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2011 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2012 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2013 Toyota Scion Tc Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.