Toyota Keyless Entry Remote Fob Programming Instructions Page 2
Keyless Entry Remote Fob Programming Instructions Available for the following Toyota models.
Click below to select your model.
| Model | Year | |
|---|---|---|
| Toyota RAV4 | 1996 | Programming Instructions |
| Toyota RAV4 | 1997 | Programming Instructions |
| Toyota RAV4 | 1998 | Programming Instructions |
| Toyota RAV4 | 1999 | Programming Instructions |
| Toyota RAV4 | 2000 | Programming Instructions |
| Toyota RAV4 | 2001 | Programming Instructions |
| Toyota RAV4 | 2002 | Programming Instructions |
| Toyota RAV4 | 2003 | Programming Instructions |
| Toyota RAV4 | 2004 | Programming Instructions |
| Toyota RAV4 | 2005 | Programming Instructions |
| Toyota RAV4 | 2006 | Programming Instructions |
| Toyota RAV4 | 2007 | Programming Instructions |
| Toyota RAV4 | 2008 | Programming Instructions |
| Toyota RAV4 | 2009 | Programming Instructions |
| Toyota RAV4 | 2010 | Programming Instructions |
| Toyota RAV4 | 2011 | Programming Instructions |
| Toyota RAV4 | 2012 | Programming Instructions |
| Toyota RAV4 | 2013 | Programming Instructions |
| Toyota RAV4 | 2014 | Programming Instructions |
| Toyota RAV4 | 2015 | Programming Instructions |
| Toyota RAV4 | 2016 | Programming Instructions |
1996 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1996 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1997 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1997 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1998 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1999 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2000 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2001 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2002 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2003 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2004 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota RAV4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2005 Toyota RAV4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Toyota RAV4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Toyota Rav-4 | 2006 | Programming Instructions |
| Toyota Rav-4 | 2007 | Programming Instructions |
| Toyota Rav-4 | 2008 | Programming Instructions |
| Toyota Rav-4 | 2009 | Programming Instructions |
| Toyota Rav-4 | 2010 | Programming Instructions |
| Toyota Rav-4 | 2011 | Programming Instructions |
| Toyota Rav-4 | 2012 | Programming Instructions |
| Toyota Rav-4 | 2013 | Programming Instructions |
| Toyota Rav-4 | 2014 | Programming Instructions |
| Toyota Rav-4 | 2015 | Programming Instructions |
| Toyota Rav-4 | 2016 | Programming Instructions |
2006 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Rav-4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2006 Toyota Rav-4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Rav-4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2007 Toyota Rav-4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Rav-4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2008 Toyota Rav-4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Rav-4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2009 Toyota Rav-4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Rav-4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2010 Toyota Rav-4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Rav-4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2011 Toyota Rav-4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Rav-4 vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2012 Toyota Rav-4 Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Toyota Rav-4 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Toyota Sequoia | 2000 | Programming Instructions |
| Toyota Sequoia | 2001 | Programming Instructions |
| Toyota Sequoia | 2002 | Programming Instructions |
| Toyota Sequoia | 2003 | Programming Instructions |
| Toyota Sequoia | 2004 | Programming Instructions |
| Toyota Sequoia | 2005 | Programming Instructions |
| Toyota Sequoia | 2006 | Programming Instructions |
| Toyota Sequoia | 2007 | Programming Instructions |
| Toyota Sequoia | 2008 | Programming Instructions |
| Toyota Sequoia | 2009 | Programming Instructions |
| Toyota Sequoia | 2010 | Programming Instructions |
| Toyota Sequoia | 2011 | Programming Instructions |
| Toyota Sequoia | 2012 | Programming Instructions |
| Toyota Sequoia | 2015 | Programming Instructions |
| Toyota Sequoia | 2016 | Programming Instructions |
2000 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2000 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2001 Toyota Sequoia Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2002 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2002 Toyota Sequoia Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2003 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2003 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2004 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2005 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2006 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2007 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2008 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2009 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sequoia vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2010 Toyota Sequoia Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Toyota Sequoia Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Toyota Sienna | 1998 | Programming Instructions |
| Toyota Sienna | 1999 | Programming Instructions |
| Toyota Sienna | 2000 | Programming Instructions |
| Toyota Sienna | 2001 | Programming Instructions |
| Toyota Sienna | 2002 | Programming Instructions |
| Toyota Sienna | 2003 | Programming Instructions |
| Toyota Sienna | 2004 | Programming Instructions |
| Toyota Sienna | 2005 | Programming Instructions |
| Toyota Sienna | 2006 | Programming Instructions |
| Toyota Sienna | 2007 | Programming Instructions |
| Toyota Sienna | 2008 | Programming Instructions |
| Toyota Sienna | 2009 | Programming Instructions |
| Toyota Sienna | 2010 | Programming Instructions |
| Toyota Sienna | 2011 | Programming Instructions |
| Toyota Sienna | 2012 | Programming Instructions |
| Toyota Sienna | 2013 | Programming Instructions |
| Toyota Sienna | 2014 | Programming Instructions |
| Toyota Sienna | 2015 | Programming Instructions |
| Toyota Sienna | 2016 | Programming Instructions |
1998 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1998 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1999 Toyota Sienna Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2000 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2000 Toyota Sienna Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2001 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2001 Toyota Sienna Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2002 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2002 Toyota Sienna Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2003 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2003 Toyota Sienna Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2004 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2004 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2005 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2006 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2007 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2008 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2009 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Sienna vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2010 Toyota Sienna Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Toyota Sienna Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Toyota Solara | 1998 | Programming Instructions |
| Toyota Solara | 1999 | Programming Instructions |
| Toyota Solara | 2000 | Programming Instructions |
| Toyota Solara | 2001 | Programming Instructions |
| Toyota Solara | 2002 | Programming Instructions |
| Toyota Solara | 2003 | Programming Instructions |
| Toyota Solara | 2004 | Programming Instructions |
| Toyota Solara | 2005 | Programming Instructions |
| Toyota Solara | 2006 | Programming Instructions |
| Toyota Solara | 2007 | Programming Instructions |
| Toyota Solara | 2008 | Programming Instructions |
1998 Toyota Solara Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Toyota Solara Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
1999 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1999 Toyota Solara Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2000 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2000 Toyota Solara Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2001 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2001 Toyota Solara Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2002 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2002 Toyota Solara Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2003 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2003 Toyota Solara Key Programming Instructions
Have your master Toyota key at hand (black key)
- Insert black programmed key into ignition.
- Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
- Press and release brake pedal 6 times within 20 seconds of step 2.
- Remove black key from ignition switch.
- Insert new unprogrammed key into ignition within 10 seconds of step 4.
- Press and release accelerator pedal once within 10 seconds of step 5.
- Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
- Within ten seconds of inserting key into ignition press and release accelerator pedal once.
- Immobilizer warning lamp will flash and after one minute the lamp will shut off.
2004 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2004 Toyota Solara Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2005 Toyota Solara Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2006 Toyota Solara Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2007 Toyota Solara Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota Solara Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Solara vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2008 Toyota Solara Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1995 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1995 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1996 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1996 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1997 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1997 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1998 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
1999 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2000 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2001 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2002 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2003 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2004 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2005 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2006 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2007 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2008 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2009 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tacoma vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2010 Toyota Tacoma Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2017 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2018 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2019 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2020 Toyota Tacoma Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Toyota Tundra | 2003 | Programming Instructions |
| Toyota Tundra | 2004 | Programming Instructions |
| Toyota Tundra | 2005 | Programming Instructions |
| Toyota Tundra | 2006 | Programming Instructions |
| Toyota Tundra | 2007 | Programming Instructions |
| Toyota Tundra | 2008 | Programming Instructions |
| Toyota Tundra | 2009 | Programming Instructions |
| Toyota Tundra | 2010 | Programming Instructions |
| Toyota Tundra | 2011 | Programming Instructions |
| Toyota Tundra | 2012 | Programming Instructions |
2003 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tundra vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2003 Toyota Tundra Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tundra vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2004 Toyota Tundra Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tundra vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2005 Toyota Tundra Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Tundra vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2006 Toyota Tundra Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota Tundra Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Toyota Venza | 2009 | Programming Instructions |
| Toyota Venza | 2010 | Programming Instructions |
| Toyota Venza | 2011 | Programming Instructions |
| Toyota Venza | 2012 | Programming Instructions |
| Toyota Venza | 2013 | Programming Instructions |
2009 Toyota Venza Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota Venza Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota Venza Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota Venza Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Toyota Venza Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Toyota Yaris | 2007 | Programming Instructions |
| Toyota Yaris | 2008 | Programming Instructions |
| Toyota Yaris | 2009 | Programming Instructions |
| Toyota Yaris | 2010 | Programming Instructions |
| Toyota Yaris | 2011 | Programming Instructions |
| Toyota Yaris | 2012 | Programming Instructions |
| Toyota Yaris | 2013 | Programming Instructions |
| Toyota Yaris | 2014 | Programming Instructions |
| Toyota Yaris | 2015 | Programming Instructions |
2007 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Yaris vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2007 Toyota Yaris Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Yaris vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2008 Toyota Yaris Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Yaris vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2009 Toyota Yaris Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Yaris vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2010 Toyota Yaris Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Yaris vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2011 Toyota Yaris Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds, Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Within 40 seconds, Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)
- Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Yaris vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2012 Toyota Yaris Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Toyota Yaris Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
